English 
T: +86-15817577177
E: Aimee@Topfive-Cable.Com
E: Aimee@Topfive-Cable.Com
No.1 Industrial Park, Tang Lian Road, Tangxia Town, Dongguan City, China.
I-PEX 20474-030E-12
1. Pitch: 0.4MM
2. Pin Number: 30P
3. 100% Original I-PEX
4. SPQ: 5000PCS
5. MOQ: 100PCS
6. Lead time: 5-10 days
1) Detection and judgment of terminal wire burnout fault
In the circuit of the power system, where the wire is grounded, the terminal wire is burned to where it is burned. The junction between the burned out and the intact part can be regarded as the grounding of the wire; if the terminal wire is burned to the wiring part of an electrical device , It indicates that the electrical equipment is faulty.
2) Detection and judgment of short circuit, open circuit, and poor contact between terminal wires
The terminal wire is squeezed and impacted from the outside, causing damage to the wire insulation in the terminal wire, resulting in a short circuit between the wires.
The terminal wire is squeezed and impacted from the outside, causing damage to the wire insulation in the terminal wire, resulting in a short circuit between the wires.
When judging, the terminal wire connectors at both ends of the electrical equipment and the control switch can be disassembled, and the electric meter or test lamp can be used to detect the short circuit of the circuit.
In addition to the obvious breaking phenomenon, common faults mostly occur between the wire and the wire terminal. After some wires are disconnected, the outer insulation layer and the wire terminals are intact, but the inner core wire of the wire and the wire terminals are disconnected. When judging, you can do a tensile test on the conductive wire and the wire terminal that is suspected to be open. During the tensile test, if the wire insulation layer becomes thinner, it can be confirmed that the wire is open.
The circuit is in poor contact, and the fault mostly occurs in the connector. When the fault occurs, it will cause the electrical equipment to not work normally. When judging, turn on the power of the electrical equipment, touch or pull the relevant connector of the electrical equipment, when you touch a connector, the electrical equipment works suddenly and abnormally, indicating that the connector out of order.
When judging, the terminal wire connectors at both ends of the electrical equipment and the control switch can be disassembled, and the electric meter or test lamp can be used to detect the short circuit of the circuit.
In addition to the obvious breaking phenomenon, common faults mostly occur between the wire and the wire terminal. After some wires are disconnected, the outer insulation layer and the wire terminals are intact, but the inner core wire of the wire and the wire terminals are disconnected. When judging, you can do a tensile test on the conductive wire and the wire terminal that is suspected to be open. During the tensile test, if the wire insulation layer becomes thinner, it can be confirmed that the wire is open.
The circuit is in poor contact, and the fault mostly occurs in the connector. When the fault occurs, it will cause the electrical equipment to not work normally. When judging, turn on the power of the electrical equipment, touch or pull the relevant connector of the electrical equipment, when you touch a connector, the electrical equipment works suddenly and abnormally, indicating that the connector out of order.
Contact Infos:
1. E-mail:Aimee@Topfive-Cable.Com
2. Skype ID: lucialiu50
Hot Tags: I-PEX 20474-030e-12, manufacturers, suppliers, factory, customized, wholesale, price, 51146-5P TO FI-S6S Assembly Wires, MOLEX 90142-0034 TO 90142-0034 Assemly Wires, FI-RE51HL TO DF13-30DS LVDS CABLE, EHR-6 TO EHR-4 WIRE Harness, FI-X30HL TO DF20A-20DS LVDS CABLE, ZHR-10 TO ZHR-10 WIRE Harness
I-PEX 20474-030E-12
1. Pitch: 0.4MM
2. Pin Number: 30P
3. 100% Original I-PEX
4. SPQ: 5000PCS
5. MOQ: 100PCS
6. Lead time: 5-10 days
1) Detection and judgment of terminal wire burnout fault
In the circuit of the power system, where the wire is grounded, the terminal wire is burned to where it is burned. The junction between the burned out and the intact part can be regarded as the grounding of the wire; if the terminal wire is burned to the wiring part of an electrical device , It indicates that the electrical equipment is faulty.
2) Detection and judgment of short circuit, open circuit, and poor contact between terminal wires
The terminal wire is squeezed and impacted from the outside, causing damage to the wire insulation in the terminal wire, resulting in a short circuit between the wires.
The terminal wire is squeezed and impacted from the outside, causing damage to the wire insulation in the terminal wire, resulting in a short circuit between the wires.
When judging, the terminal wire connectors at both ends of the electrical equipment and the control switch can be disassembled, and the electric meter or test lamp can be used to detect the short circuit of the circuit.
In addition to the obvious breaking phenomenon, common faults mostly occur between the wire and the wire terminal. After some wires are disconnected, the outer insulation layer and the wire terminals are intact, but the inner core wire of the wire and the wire terminals are disconnected. When judging, you can do a tensile test on the conductive wire and the wire terminal that is suspected to be open. During the tensile test, if the wire insulation layer becomes thinner, it can be confirmed that the wire is open.
The circuit is in poor contact, and the fault mostly occurs in the connector. When the fault occurs, it will cause the electrical equipment to not work normally. When judging, turn on the power of the electrical equipment, touch or pull the relevant connector of the electrical equipment, when you touch a connector, the electrical equipment works suddenly and abnormally, indicating that the connector out of order.
When judging, the terminal wire connectors at both ends of the electrical equipment and the control switch can be disassembled, and the electric meter or test lamp can be used to detect the short circuit of the circuit.
In addition to the obvious breaking phenomenon, common faults mostly occur between the wire and the wire terminal. After some wires are disconnected, the outer insulation layer and the wire terminals are intact, but the inner core wire of the wire and the wire terminals are disconnected. When judging, you can do a tensile test on the conductive wire and the wire terminal that is suspected to be open. During the tensile test, if the wire insulation layer becomes thinner, it can be confirmed that the wire is open.
The circuit is in poor contact, and the fault mostly occurs in the connector. When the fault occurs, it will cause the electrical equipment to not work normally. When judging, turn on the power of the electrical equipment, touch or pull the relevant connector of the electrical equipment, when you touch a connector, the electrical equipment works suddenly and abnormally, indicating that the connector out of order.
Contact Infos:
1. E-mail:Aimee@Topfive-Cable.Com
2. Skype ID: lucialiu50
Hot Tags: I-PEX 20474-030e-12, manufacturers, suppliers, factory, customized, wholesale, price, 51146-5P TO FI-S6S Assembly Wires, MOLEX 90142-0034 TO 90142-0034 Assemly Wires, FI-RE51HL TO DF13-30DS LVDS CABLE, EHR-6 TO EHR-4 WIRE Harness, FI-X30HL TO DF20A-20DS LVDS CABLE, ZHR-10 TO ZHR-10 WIRE Harness
Topfve cable was established in 2010 years.Our products are widely used in electrical products, industrial display screen, Medical display, UAV unmanned aerial vehicle and so on.
